2024 Mustang EcoBoost Race Intercooler Install | Race Car Side Hustle

3 Hardware Store Trips Later… The Engine Cart Finally Stands

This Build Could Go a LOT of Different Ways…

Race Car Side Hustle: Paying for Red Fox Parts one Job at a Time!

Prototype Parts, Experimental Tuning, Race Car Side Hustle, & SECRETS!

Our "Little" Secret...

TR6060 Reassemble

TR6060 Bearing Replacement: Harder Than It Looks, but I Got It Done

How to Disassemble a TR6060 (2009 GT500) - Every Step, Every Detail

Goodbye Interior... Building My Dream Fox Body Drag Car

I Finally Admitted I Needed Help... So We Pulled the Transmission

This Could Have Ended Really Bad...

I Finally Installed the Clutch This Coyote Deserves

My Coyote Needed A Complete PCV Overhaul

I Was Ready to Reinstall The Transmission Until I Found This

The Throwout Bearing Was DESTROYED… So I Tore Into The TR6060

The Throwout Bearing FAILED After Mustang Week… So We Pulled The Transmission

This Ford Explorer ST Just Funded The Race Car

@uprproducts Front End Install - 250 lbs+ LIGHTER!!!

I’m Rebuilding the Entire Front End… Here’s What I Chose from @uprproducts

Dialing In Ride Height + Front End Build Begins

ZERO MILE Automotive INVESTMENT or GAMBLE?

The Fox Rear Suspension is ALMOST Finished! UPR Springs & Team Z ARB Install

I Finally Drove It Again… And It Feels INSANE

The MOST UNDER-VALUED Upgrade for a Race Car!

Truth about Funding a Race Car & Chasing 9s

First @HoustonSpeedFreaks Twin Turbo Track Test at Import Face-off

Built Ford 8.8 (Part 10): Final Assembly of Axles & Brakes

Ford 8.8 Install, but STILL NOT DONE!

8.8 Rear End Build (Part 9): Paint the Housing Chassis Black

Mustang 8.8 Build (Part 8): @TeamZMotorsports Rear Housing Brace

8.8 Rear Axle Build (Part 7): @TeamZMotorsports Lower Control Arm Brackets

Fox Body 8.8 Build (Part 6): @uprproducts Extreme Spherical Bearing Install

8.8 Rear End Build (Part 5): Differential Assembly

Ford 8.8 Axle Build (Part 4): 31 Spline @MoserEngineering Axles

Ford 8.8 Build (Part 3): @uprproducts 8.8 Rear End Front Braces

Ford 8.8 Rear End (Part 2): Welded Axle Tubes

8.8 Rear End Rebuild (Part 1): Tear Down + Deep Clean (Red Fox)

Budget Built Coyote: Machine Shop or SEND IT!?!?

Budget Built Coyote Looked ROUGH...Until...

Bare Cage to Accessorized!

NEW X-PIPE EXHAUST - Same Mufflers, Totally DIFFERENT SOUND!

From Street Car to Race Car; Part 3 of the '65 Mustang Roll Cage.

Days of Work...Barely Any Progress; 1965 Mustang Roll Cage Part 2

Point of No Return - 1965 Mustang gets CAGED

Fox Body Brake Upgrade...and Why I Didn't Finish It

Mustang Week 26 All Oval Runs

Changing Anti-Squat on My ’65 Mustang

Mustang Week 26 HPDE Session 4

Mustang Week 26 HDPE Session 3

Mustang Week 26 HPDE Session 2

Mustang Week 26 HDPE Session 1

Mustang Week Texas 26: Feedback

Mustang Week Texas 26 Day 4: Car Show, Drifting, & Burnout Comp

Mustang Week Texas 26 Day 3: Drag Day

Mustang Week Texas 26 Day 2: Track Day

Mustang Week Texas 26 Day 1: Kickoff Party

Fox Body Pinch Weld Repair + Lift Point Upgrade

Prepping the '65 Mustang for the CRAZIEST Week of Racing Yet

Wilwood Hub Rebuild + An Unexpected Fire