[AN-07] - Zener Voltage Regulator Design (Step-by-Step) | Easy Explanation

[AN-25]-Capacitor Selection & Types Explained | ESR, Ripple Current, Voltage Rating & Parameters

[AN-24] - How to Select the Right Resistor? | Types, Ratings & Parameters

[AN-23] -Comparator, Inverting, Non-Inverting Amplifier & Schmitt Trigger | Variable Duty Generation

[AN-22] - Op-Amp Common Mode Voltage Range & Slew Rate Explained

[AN-21] - Op-Amp Parameters Explained | Input Offset Voltage, CMRR, Bias Current, ACM & AD

[AN-03] - Diode Conduction and Switching Loss Calculation (Step-by-Step Tutorial)

[Class-18] - Four Layer Stack Definition and Routing Plan

[Class-1] - Introduction of Altium Designer

[Class-5] - IC Symbol Creation

[AN-05] - Diode Heat Sink Design

[AN-11] - BJT Loss Calculation Explained | Conduction & Switching Loss (Step-by-Step)

[Class- 11] - Buck Converter PCB Layout Example

Design a Flyback Transformer from Scratch (DCM Method)

[AN-10] - BJT Saturation & Overdrive Factor (With Practical Examples)

Sanjay Maniktala | RCD Snubber Design for Flyback Converter | Practical Design Explained

Reset in Flyback || Zener Clamp || Sanjay Maniktala

[AN-15] - Stop Burning MOSFETs! Understand VGS(th), Rds(on) & Id

[AN-20] - Relay Selection & Applications | Complete Guide for Electronics Engineers

[AN] - Analog Circuit Design Demo Class

[AN-19] - MOSFET Gate Drive Application Circuits | High-Side, Low-Side & Practical Design

[AN-14] - BJT De-rating BJT Selection Parameters

[AN-18] - MOSFET Snubber Design | Series and Shunt Snubber

[AN-17] - MOSFET Gate Resistance Calculation

[AN-16] - Understand MOSFET Gate Profile, Conduction & Switching Loss

[AN-12] - BJT LED Driver Circuit (With Calculations) | Step-by-Step Guide

[AN-13] - BJT Application Circuit Design | Real Examples Explained

[AN-09] - TVS & ESD Diode Selection Explained | Don’t Damage Your Circuit!

[AN-08] - Diode De-rating Explained | Practical Design Tips You Must Know

[AN-06] - Diode Datasheet Explanation

[AN-04] - Diode Switching Loss and Thermal Design

[AN-02] - Diode VRRM and Static Characteristics

[AN-01] - Diode Introduction

[Class-19] - High Speed Signal Routing

Complete PCB Design Course | Altium Designer | Beginner to Industry Level

[Class-10] - Floor Planning and Component Placement

[Class-13] - 4 Layer PCB Layout Design

[Class-14] - Trace Width, Via , DRC

[Class- 9]- Connector and SOIC-8 Footprint Design

[Class-12] - Routing and PCB Design Guidelines

[Class-17] - High Voltage Power Supply PCB Layout

[Class-20] - PCB Design Constraints

[Class-21] - Gerber File Generation in Altium Designer | PCB Manufacturing Output Explained

[PCB-16] - Four Layer PCB Component Placement

[Class-15] - Multi Page Schematic Design

[Class-8] - LED Symbol Creation and SMT Capacitor Footprint

[ Class - 7 ] - Layer Stack up

[Class-6] - Footprint Design

[Class-4] - Schematic Design

[Class-2] - Symbol Creation

High-Side MOSFET Bootstrap Driver | LTspice Simulation | Isolated

Series Voltage Regulator in LTspice | Complete Simulation Tutorial

Buck Converter Inductor Design Using Core Geometry (Kg) – Complete Example

Altium PCB Design Master Class | Complete PCB Design From Scratch

Power Factor & Harmonic Current Explained | IEC 61000-3-2 Simulation

Non-Isolated ZCD Design & Simulation | Zero Cross Detector

How to Generate +12V and −20V Dual Supply Using LT1945 in LTSpice

How to Design a Closed Loop Synchronous Buck Converter in LTSpice

Adjustable Buck Converter Design in LTspice | ADP2370 Simulation (15V to 0.8–14V Output)

MOSFET Gate Current vs Power Loss Simulation | Simulation & Explanation