Don’t take anything for granted on a breakdown & test reed switches before changing components 

How I breakdown a breakdown in section proving components saving time and money 

Thermal cut out how we MOD this machine and using it as a safety device and how they work

Break down plus tips and tricks on how to test a RTD/PT100

How safety relays work and how to fault find using Pilz S4

Testing a three phase heater under real life break down scenario 

How to read and use electrical drawings on the breakdown on a parts washer.

Breakdown of a potentiometer how to fault find & install new one along with signal voltage to VFD

Motor overload what they do and how to set them, motor set on fire due to mpcb being set wrong

How to check if you have a PNP or NPN sensor if you don’t have your data sheet or no markings

Encoders different types incremental and absolute, how they work and how to test them.

Testing a single phase motor with capacitor, insulation resistance test also checking resistant.

SY Cable how to terminate, make off step by step practical, after finding some shocking termination

Fnirsi SG-003A signal generator what it does and how to use it

Variable frequency drive VFD how they work and how to test them

Latching circuit understanding why we use them and how to wire them up to contacts and relays

Load cells how they work and how to test them

Temperature transmitter how it works and how to test it

Temperature transmitter how they work and how to test them

Thermocouple how they work and how to test them

PNP/NPN what they are how they work and how they work in sensors and the wiring of the sensor

Testing sensors and how ultrasonic sensor work.

Test equipment of a maintenance engineer fluke 1587 fc, flir thermal clamp meter and more

Testing a three phase motor and what voltage to use when doing a insulation resistance test (IR)

Electronic motor brake what they are, how they work and how to test them

Float switches, how they work and how to test them 

Break down video on a low level on our RO unit and float switches in they working environment 

Standstill monitoring safety relay what it does and how it works.

Break down on a vac pump where coupling sheared off, along with what a coupling is & what it’s for.

What a potentiometer is, what it does, how it works and how to test them.

Pilz how the reset modes work what they mean and why you use them.

Understanding pilz safety relay how they work and how to wire them up using a e-stop

How to understand pilz safety relay how they work and how to wire a mag switch into the pilz relay.

Understanding pilz safety relay how the work and how to wire a coded mag safety switch.

Understanding pilz safety relay how they work and who to wire them to components

How a three phase heater will be control by two solid state relay and what to watch out for !!

20 July 2023

When fault finding always take everything in don't dismiss something until tested#engineering

Fault finding why three phase heater not reaching set point (how three pole thermostat works)

Talking through electrifash panel Part.5 and how a transformer, thermal fuse and cartridge heaters

Fault finding reed switch and pneumatic cylinder

Talking through electrical panel & drownings Part.4 & how safety relays work

Talking through electrical panel & drownings Part.3 & how PLC work

Talking through electrical panel & drownings Part.2 how solid state relays work (SSR)

Talking through a electrical panel & drains part1. Solid state relay #engineering #electrical

Reading and fault finding PLC Siemens S7-300

Testing a single phase motor with capacitor, insulation resistance test also checking resistant.

Testing a three phase motor by Insulation resistance test and resistance checking the windings

RTD/PT100 (resistant temperature device & how to test, using fluke 1587fc

Panel testing tripped three phase vibrator motor, using fluke clamp meter.

Little tech tip to pick up  metal swarf if your Henry pack up.

Day in life of a maintenance engineer this time Peugeot Partner has decided to shit it coolant.

Day in the life of a maintenance engineer, how to on centre dotting

Day in the life of a maintenance engineer, on this job tracking conveyor belt.

Maintenance engineer toolbox tour (live in)