Patching the floors in the 1970 Monte Carlo

Thought the P1cruiser was good to go.

Wiring up the dakota digital vhx box, with pfewh1201 and painless wiring harness.

Reworking the LS harness on the 1970 Monte Carlo.

Starting on the interior wiring in the 1970 Monte Carlo.

Which one sounds better 5th gen camaro vs. Lsx PT cruiser?

Running both wiring harnesses in the 1970 Monte carlo

Wiring the tail light section on the 1970 Monte Carlo.

Starting to tear into the 1970 Monte carlo.

New project car getting dropped off.

Fixing the oil pressure and steering shaft issues on the P1cruiser

LSX PT Cruiser. was it ready for RMRW?

Fixing problems less than 48 hours before raceweek

P1cruiser 1st time moving with the LS swap

1st start on the P1cruiser. Lsx PT cruiser.

Lsx PT cruiser is starting to nickle and dime me, also got the exhaust finished.

Finally found a set of headers for the P1cruiser. And a solution to the cooling system

Finishing up the wiring on the P1cruiser.

Fan shroud and fuel lines for the P1cruiser.

Will the P1cruiser be ready in time?

Knocking off a few things on the checklist for the P1cruiser.

Update on the P1cruiser. Engine rebuilt and waiting on parts.

G-bodys in junkyards 1985 Oldsmobile Cutlass 442.

Painting the engine for the P1cruiser, and doing work on the wheel wells.

Got one of the G-bodys out of hibernation.

Testing out the wiring in the P1cruiser.

Ive been a little all over the place making some progress on the P1cruiser.

Rear ride height adjusted, and starting to mock up on the steering shaft.

The P1cruiser is low.

New tires for the P1cruiser.

This is definitely going to look good on the P1cruiser.

New Led lights from Oxilam for the Silverado. Discount code DashsGarage

NEW wheels for the P1cruiser are in. Also put the front suspension back on.

Test fitting wheels on the P1cruiser.

Rear brakes installed on the P1cruiser and pedal box mocked up.

Motor mounts for the P1cruiser.

The back of the P1cruiser is close to being finished up.

Wheel tubs for the P1cruiser came out better than I thought.

Making the mount for the fuel cell and bolting the 3rd member to the 9-inch.

P1cruiser update and mocking up the fuel cell.

Cutting the axles for the P1cruiser, and finally ordered the rest of the parts for the rear-end

Tearing into the 6.0 for the P1cruiser

P1cruiser 6.0 and 4l80e test fit, and the rear-end redone.

Found the 6.0 LS for the P1cruiser and getting back to fixing the rear-end

Big mistake on the P1cruiser rear-end and helping my neighbor with his Monte carlo SS

The 4 link for the P1cruiser is in place.

My 1st road trip on the Streetglide

Went looking for a motor for the P1cruiser, left with something else.

Decided to get the elco out for a little drive around the block.

The frame for the P1cruiser is complete.

Now there is room! Cutting out the wheel wells to make room for the ford 9inch

Wheel mockup on the P1 cruiser. And getting started on the backhalf

Testing out the new torque converter in Mona Lisa.

Old School Co. Springs 2nd annual show&shine car show.

Front crossmember about 90%finished in the P1cruiser.

I ran into @tavarish and I had to ask, was the PT Cruiser really that bad?

Making some progress on the LS Cruiser.

Got ‎⁨@grindschool⁩  out in Mona Lisa, then talked cars and plans for both channels.

Mustang 2 front suspension for the Pt cruiser is starting to take shape.

Starting on assembling the Mustang 2 crossmember for the Pt cruiser.