alishanmao

Yes I have lived my 1980s and I do not think I actually looked like this? but this AI trend, made me curious and I can only laugh watching this. what do you think? will you do yours 1980s AI picture? Just ask ChatGPT.

#ai #chatgpt #gpt #1980s #1985 #nostalgic #dude #old #memories

2 days ago | [YT] | 29

alishanmao

AliShanMaoRC Tips: Set your failsafe to actually cut throttle to zero, not just hold last position. Because If you lose signal over a road or near people, 'hold' can carry your RC helicopter or Aircraft, somewhere you really don't want it going.

Join my channel to access all my premium highly valuable How to video Tutorials and members only content: youtube.com/@alishanmao/join
My Highly Recommend Gear and Links→ linktr.ee/alishanmaorc


#alishanmaorc #3dprintable #rchelicopter #rchobby #scalerc

2 weeks ago | [YT] | 45

alishanmao

Hey Pilots! 3 months Limited Sales of AliShanMaoRC Scale Helicopters fuselage Kits is Up. Check it out at alishanmaorc.com/

#alishanmaorc #3dprintable #rchelicopter #rchobby #scalerc

2 weeks ago | [YT] | 22

alishanmao

AliShanMao RC Tips. Today I bring you Two letters. CG. The Center of Gravity. CG Matters more than any radio or flight controller settings. no matter how perfect setup you make for your RC Helicopter or airplane or a drone, if CG is not balanced, you are definitely looking for flight troubles and or beautiful crashes.

Remember a nose heavy RC aircraft may fly, but a tail heavy will fight you like a an angry wife that you refused to give a bank card to for shopping :D

Join my channel to access all my premium highly valuable How to video Tutorials and members only content: youtube.com/@alishanmao/join

My Highly Recommend Gear and Links→ linktr.ee/alishanmaorc

#alishanmaorc #3dprinted #3dprintedrc #3dprintable #stlfiles #stl #downloadstl #rchelicopter #flywing #scalerc #rcbuilds #3dprintedhelicopter #russianhelicopter #rcflying #3dprintedaircraft #yardpilot

2 weeks ago | [YT] | 30

alishanmao

Many people ignore blade tracking when setting up RC Helicopters. This is actually one of the most critical thing to check and fix. because if blade tracking is even slightly off, your helicopter doesn't just vibrate slowly but this vibration can put stress to your swash and rotor linkages. loosen screws or other parts. and cause crashes in the end. How to find if blades are tracking properly? easy way, Take off, hover at your eye levels. see if one of the blades is spinning slightly up or down than other blade? you will know your blade tracking is off. For the fix, I will post later.

Join my channel to access all my premium highly valuable How to video Tutorials and members only content: youtube.com/@alishanmao/join

My Highly Recommend Gear and Links→ linktr.ee/alishanmaorc

#alishanmaorc #3dprintable #rchelicopter #rchobby #scalerc

2 weeks ago | [YT] | 45

alishanmao

AliShanMaoRC Tips:
Many people overlook the Dual rates and expo settings in their model setup. Let me tell you, these aren't just for 3D pilots. Even if you are a beginner pilot and flying a scale GPS based helicopter, running 70-80% dual rates with 30-40% expo on cyclic can make your helicopter hover corrections smoother and way less twitchy. Makes it easier to control your helicopter.

If you like you can book a 30-min call and I can guide you on how to setup your helicopter model with correct dual rates and expos: buymeacoffee.com/alishanmao

Join my channel to access all my premium highly valuable How to video Tutorials and members only content: youtube.com/@alishanmao/join

My Highly Recommend Gear and Links→ linktr.ee/alishanmaorc

#alishanmaorc #3dprinted #3dprintedrc #3dprintable #stlfiles #stl #downloadstl #rchelicopter #flywing #scalerc #rcbuilds #3dprintedhelicopter #russianhelicopter #rcflying #3dprintedaircraft #yardpilot

2 weeks ago | [YT] | 13

alishanmao

Support my work: buymeacoffee.com/alishanmao
To My Loyal Supporters. 263 supporters have bought me a coffee over the years while I have been busy building rc helicopters for all of you to enjoy and providing sincere support to anyone who needed. All that coffee :) its fuel for me. Thank you so much for all your support. New designs are coming soon. Which Helicopter Should I design next?

#support #buymeacoffee #rchelicopter #3dprinted #3dprintable #3dprintedrc #scalerchelicopters #alishanmaorc

2 weeks ago | [YT] | 18

alishanmao

One question I often receive from my followers: Does my EdgeTx RC Helicopters YML bundle cover any OMPHobby / Goosky / Trex helicopters?

Well answer is Yes — one universal 3D profile, tuned and tested, works with every small to 700 size 3d helicopters. No guessing which file is 'yours.'

Follow my Linktree for all my highly recommended gear and links: linktr.ee/alishanmaorc

#alishanmao #alishanmaorc #edgetx #helicopters #yml #models #edgetxhelis

2 weeks ago | [YT] | 15

alishanmao

https://youtu.be/o0Pvl4pcKHw
TX16s MK3 is an impressive radio, and as much as I love it, I am so much digging the new GX15. I know there is no comparison here. one is a fully featured high end radio and one is for LOS Pilots but still, GX15 offers so much more than you can expect. Watch full review and let me know what you think.

#alishanmaorc #3dprinted #3dprintedrc #3dprintable #stlfiles #stl #downloadstl #rchelicopter #flywing #scalerc #rcbuilds #3dprintedhelicopter #russianhelicopter #rcflying #3dprintedaircraft #yardpilot

2 weeks ago | [YT] | 4

alishanmao

tinyurl.com/ymlguide
Have you ever used EdgeTx companion to import YML models to your EdgeTx radios just to find out that you conveniently overwritten all your existing models with one you just imported?

Yikes! I know, its the heart sinking moment we all have faced and there is no undoing this. Unless if you were smart enough to keep multiple backups like me 😁

Forget about Edgetx companion, forget about accidental overwrite, and Learn to move EdgeTX model YML files from radio to radio as easy as copy paste with my personally used, proven to work method 😍

Consider the guide cost a friendly coffee to AliShanMao. Love ya all. 💖

⚙️ RC pilots keep asking what gear I use.
It's all listed here: linktr.ee/alishanmaorc
Tools, upgrades and my designs.

#edgetx #radiomaster #yml #import #models #hack #guide #alishanmaorc

3 weeks ago | [YT] | 14