Drone Science Tech
Hi
welcome to my channel
DIY Projects,PCBs,All Types Drone, Rc Airplane,Rc Car, Rc Helicopter, Rc Boat , 3D Printer, Homemade Projects, Robot, Arduino projects , Unboxing, Review and technical Videos Available
I try my best in making videos and try to make every video of a different type
Keep support 👍👍
Keep watching 👍👍
Press Bell 🔔 icon And Get Notifications
Thank you
Buisness enquiry :
Dronescincetech1993@gmail.com
Drone Science Tech
🛑 This video will be uploaded this evening 6:00 Pm.
you can watch it by visiting the channel page.
🚁 It is a very low-budget RC trainer plane.
👍 We will soon be testing it with an Arduino flight controller.
2 weeks ago | [YT] | 21
View 1 reply
Drone Science Tech
▶️ This is a project from a year ago that I couldn't complete for some reason, but I’ve finally finished it now.
👍 It will be uploaded very soon.
🛑 It is a completely DIY build.
I determined the design based on the wing length and calculated its load capacity.
▶️ I used an Arduino-based transmitter and receiver setup, keeping the cost very low.
🚁 Since I am still a novice pilot, I haven't been able to fly it perfectly yet.
🤔 I probably need more practice.
High-end transmitters feature superior joystick gimbals, whereas the joysticks on this one aren't quite as good, making it a bit tricky to fly.
That said, it’s still fun to use.
🛑 Next, I plan to incorporate an Arduino flight controller so I can fly it better as a beginner.
I hope you like it.
3 weeks ago | [YT] | 34
View 2 replies
Drone Science Tech
Like or Dislike ????
1 month ago | [YT] | 54
View 8 replies
Drone Science Tech
🛑 I have experimented with many transmitters.
▶️ But I have built this new one to be fully functional, offering a great experience on a low budget.
It features trim functions, a display, toggle switches, and dual antennas, giving it a professional look.
I incorporated dual antennas to ensure stable range, and the trim function allows for the precise trimming of any drone,Rc Plane,Rc Car etc.
▶️ A video showing it fully tested will be available on the channel soon.
1 month ago | [YT] | 39
View 5 replies
Drone Science Tech
🛑The new drone video has just been released. If you haven't seen it yet, you can watch it by visiting this link : https://youtu.be/K4kzoEaVzk4
👊 In this project, I have use a DIY Arduino flight controller, which allows you to use a frame of your own choice.
▶️ I have experimented with various frames using this setup.It is quite well-suited for outdoor flight.
It features a compact PCB that weighs only 2 grams. I have powered it using 8520 motors and a 600mAh battery
5 months ago | [YT] | 102
View 4 replies
Drone Science Tech
🛑 The drone I made with 720 motors was fine for indoor flight.
▶️ We can easily fly it outdoors in very little wind.
But this drone struggles to fly in little wind and the battery gets drained quickly.
🛑 Then after that I made a slightly bigger drone using 8520 motors.
It has only custom Design flight controller without frame.
Its propeller size is 3 inches.
When I did its outdoor flight test, the results were quite good.
This drone was struggling very little.This drone proved to be very good for learning.
👍 I also learned a lot from outdoor flying. And the battery life was also quite good.
🛑 By looking at these photos you can guess how much bigger this drone is than the small drone.
▶️ Its full video is going to come very soon. I hope you liked this video.
👍 If you liked this big drone then definitely write yes in the comment.
5 months ago | [YT] | 79
View 4 replies
Drone Science Tech
🛑 I was getting a short range with the NRF24L01 module that had a PCB antenna.
Video Out Now : Link
https://youtu.be/SlYRltaouNs
▶️ so I thought of using an NRF24L01 module with an external antenna.This would increase the range of my mini drone.
However, there was a problem: its weight was 11 grams. Therefore, it was necessary to reduce its weight.
So, I removed the antenna and replaced it with a wire. Finally, its weight came down to 2 grams.
👍 Now I am confident that my mini drone will have a range of up to 1 km.
🎉 To understand this better, please watch the full video......
6 months ago (edited) | [YT] | 44
View 5 replies
Drone Science Tech
🛑 My PCB design journey is as follows.
▶️ Before designing the PCB, I thought a lot about what shape to give it so that it would look compact.
👍 Then I choose this design.You might not like it, but I liked this design because of its small size.
👊 This transmitter PCB supports 7 channels
🛑 In upcoming videos, I will be presenting some more designs.
I hope you all like them.
6 months ago | [YT] | 54
View 0 replies
Drone Science Tech
Which Arduino Microcontroller is Lightweight ????????
6 months ago | [YT] | 5
View 1 reply
Drone Science Tech
🛑 The range of the PCB antenna module is quite limited, which makes it difficult to fly the mini drone. Only Up to 250mtr.
▶️ Therefore, I decided to modify the antenna module.This modification increased the range to up to 1 km.
However, there was a problem: the modified module was quite heavy. (About 11gm)
🛑 So, I decided to modify the antenna further. After that, its weight was reduced to only 1-2 grams, and the plan was a success.
🛑 A detailed video about this will be coming soon.so keep watching channel
6 months ago | [YT] | 42
View 1 reply
Load more