ACME

Gas Atomization Powder Production Equipment
The intermediate frequency melting furnace is placed in an appropriate place. The metal or alloy is melted and alloyed by intermediate frequency heating. The metal melt flows through the pre-heater and the guide tube to the spray plate, the high-pressure gas flows out the nozzle and breaks the metal melt into small drops. While the metal drops forms the fine metal powder, which form sub-spherical or irregular particles under the combined action of surface tension and rapid cooling of gas during falling down.



www.acme-furnace.com/

overseas@sinoacme.cn

Skip the Carousel

1 2 3 4 5

2 years ago | [YT] | 0

ACME

Plasma rotating electrode atomization equipment processes metal or alloy powders with good sphericity, fewer defects, uniform and narrow particle size distribution, low impurity content, low oxygen content and low growth, which is applied for aerospace materials and addictive manufacture of special metal-based powder material.

www.acme-furnace.com/
overseas@sinoacme.cn

Skip the Carousel

1 2 3 4

2 years ago | [YT] | 0

ACME

Mesh Belt Sinter Furnace
Mesh belt sinter furnace is mainly used for high temperature sinter of powder metallurgy ferrous and copper parts, such as oil bearing, gear, clutch plate, bushing, sleeve, etc.

www.acme-furnace.com/
overseas@sinoacme.cn

Skip the Carousel

1 2 3 4

2 years ago | [YT] | 0

ACME

Batch Type Purification Furnace
Furnace is used for purify treatment of graphite powder, graphite part, insulation materials and etc.


www.acme-furnace.com/

overseas@sinoacme.cn

Skip the Carousel

1 2 3 4 5

2 years ago | [YT] | 0

ACME

CVD Furnace(C)
Furnace is used for material CVD/CVI treatment by using hydrocarbon gases (like C3H6,CH4 ) . It has both horizontal and vertical structures.

www.acme-furnace.com/

overseas@sinoacme.cn

Skip the Carousel

1 2 3 4 5

2 years ago | [YT] | 0

ACME

Plasma Rotating Electrode Atomization Equipment
Plasma rotating electrode atomization equipment processes metal or alloy powders with good sphericity, fewer defects, uniform and narrow particle size distribution, low impurity content, low oxygen content and low growth, which is applied for aerospace materials and addictive manufacture of special metal-based powder material.

www.acme-furnace.com/

overseas@sinoacme.cn

Skip the Carousel

1 2 3 4 5

2 years ago | [YT] | 0

ACME

Dai Yu, the Chairman of ACME，was invited to attend the National Symposium on New carbon materials and make an academic report

On August 14-16, 2023, the 16th National Symposium on New Carbon Materials was held in Taiyuan, Shanxi Province. The symposium was hosted by Shanxi Institute of Coal Chemistry, Chinese Academy of Sciences and Shanxi Association of Science and Technology, and was attended by more than 400 representatives from universities, research institutes and enterprises across the country. The conference is a representative academic exchange conference in the field of carbon materials in China and is held every two years.

The conference set up three sub-sessions with the theme of "Carbon fiber, graphite and carbon-based composites", "Nanocarbon, porous carbon and structural characterization of carbon materials", and "Application of carbon materials in electrical energy storage and structural regulation", compiled a total of 212 research paper abstracts, and gathered the latest research results of China's new carbon materials research and development.

Dr. Dai Yu, Chairman of ACME, was invited to attend the conference and gave an academic report entitled "Technical Status and Prospects of" Four High and Two Coats "carbon-based Materials for third-generation semiconductors. The report describes the application status of third-generation semiconductor materials at home and abroad, analysis of the reasons for the gap between domestic silicon carbide single crystals and foreign countries, and the progress made by ACME in the research of "four high and two coats" carbon-based materials (namely high purity carbon powder, high purity silicon carbide powder, high purity graphite, high purity hard felt, silicon carbide coating, tantalum carbide coating).

The ultra-high temperature purification equipment independently developed by ACME adopts a unique composite high temperature thermochemical purification process, which breaks through the removal technology of high purity carbon powder trace impurities, and the product purity can reach more than 6N; The self-developed chemical vapor deposition equipment has broken through the key technology of TaC coating preparation, and its product performance has reached the international advanced level, realizing the independent control and industrialization of the key materials and equipment for the third generation of semiconductors.

Skip the Carousel

1 2 3

2 years ago | [YT] | 0

ACME

Vacuum Debinding and Sintering Furnace(SiC/Si3N4/AlN)
The furnace is used forreaction sintering, low pressure sintering, re-crystal sintering of carbide, nitride, oxide ceramic embryo and products. The degreasing system is optional to realize the one-time degreasing and sintering treatment of ceramic products.
www.acme-furnace.com/
overseas@sinoacme.cn
overseas@sinoacme.cn

Skip the Carousel

1 2 3 4

2 years ago | [YT] | 0

ACME

Vacuum Hot Press Furnace
Vacuum hot press furnace is widely used for all kinds of composite materials, high conduct thermal material, SiC/Si3N4/B4C ceramic materials, copper base iron power materials, iron base materials, iron-copper base power materials shaping, densification.

overseas@sinoacme.cn

www.acme-furnace.com/

Skip the Carousel

1 2 3 4 5

2 years ago | [YT] | 0

ACME

Vertical Bottom Loading Vacuum Brazing Furnace
Vacuum bottom loading furnace is used for vacuum brazing of materials like non-ferrous metal, stainless steel, titanium alloy, high temperature alloy.
overseas@sinoacme.cn

www.acme-furnace.com/

Skip the Carousel

1 2 3

2 years ago | [YT] | 0