I made my own shielded wire with home reno supplies

Homemade Water/Methanol injection system update, getting closer!

DIY water/meth injection pressure and injector flow rate testing, ITS GONNA WORK!

DIY water/meth injection system functions test, the injectors are LOUD

DIY Water/methanol controller test success!

Learning how to calibrate ADC pins on an esp32 for sensor calibration

CRAZY water/meth injection UI and learning how to wire a MOSFET! DIY water methanol injection system

DIY water/methanol with an esp32 arduino, testing and wiring, learning as I go

Homemade Water/Methanol injection system is nearly finished!

Finally, SUCCESS!! My DIY Water/Methanol injection rail is working!

DIY water methanol injection system testing. Still workin on the fuel rail

DIY water methanol injection rail finally a success!!

Adding 3 injectors to my charge tube.. why? MORE POWER YO

DIY water/meth injection kit just levelled up! Options, safeties, esp32 controller.

Homemade water/methanol injection kit? (Kaboom probably)

Why won’t my electric fan cut in on time? Let’s figure out the tune

I installed a Jeep radiator in my Silverado… how does it work?

Desperado is going to get SO MUCH COLD AIR

Super simple LS steam vent solution

Desperado quick tuning video I’ll probably do more of these

Desperados fuel gauge doesn’t work (ain’t got no gas in it)

How to turn off every warning light in your car (the illegal way don’t do this)

Desperado won’t shut off with the key.. what did I do wrong??

Making AN PTFE trans lines for my 4L80E and trucool 40K cooler - Desperado

Brand new high stall converter won’t fit.. machined incorrectly?

Desperados 4L80E is FINISHED!! Torque converter won’t fit?

How to: ESP32 Transbrake and Bump Box control. Super simple setup!

Leak testing, repairing and installing PTFE ends on AN hose. Learning as I go!

Desperado got the SICKEST Christmas gift!

NP261 2500hd transfer case disassembly, cleaning and reassembly.

Desperado trans cooler AN fittings and Hobbs switch mount

@SloppyMechanics super complex hobb switch mount

Desperado wiring and transfer case plans and stuff and things

DIY Transbrake and Bump Box wiring with only simple parts!

Trucool 40k mounted, my first time installing AN PTFE lines. Cool stuff!

Remote trans filter mount in my Silverado - Desperado

Stripped out oil feed fitting is not a good time plus 4L80E flexplate install

My exhaust is in the way of my transmission… let’s fix it! 4L80E swap in desperado

Test fitting custom trans crossmember and 4L80E swap parts in my 1500 Silverado - Desperado

Removing shift kit, corvette servo and sonnax pinless accumulator from the last 4L60E ever

Reworking a 4L80E harness for my turbo awd silverado! Desperado is getting a new transmission

3D printed goodies for 99-06 Chevy trucks

4L80E Worn input shaft, Rear End Play check with varying results!

4L80e internal assembly and endplay check struggles!

4L80E - How to install new clutches and steels, and check clearance

DIY 3D printed 4L80e PTFE seal installers how to!

4L80E accumulator delete, transbrake, installing lip seals and more!

4L80E testing electrical components and more seal replacements - reverse servo plunge depth

4L80E endplay adjustment with rollerized output shaft

4L80E (mostly) every seal replacement!

HOW TO: TransGo 4L80E AFL valve repair kit (Actuator Feed Limit valve)

4L80E Sonnax boost valve install and oil pump assembly & alignment

Over-engineered 4L80E swap crossmember build!

4L80E - installing sonnax rollerized rear output shaft bearing and bushing

4L80E internal parts cleaning, and learning a few things as I go

Science with Barry and Zach finally a success!

disassembling and inspecting my 4L80E. Learning as i go!

AWD t-case on a 4L80e! Will a NP261 32 spline input fit an NP149? Let’s find out!

AWD input shaft change to fit 4L80e? Sciencing with Barry

Desperado moves, shifts, we’re back on the road!