Fixing disgusting repair on Lemken Plough frame!

Building myself a little car shed outside my house! Completed.

Putting sleeves in a worn out Takeuchi King Post. Like new again!

Building myself a little car shed outside my house! Part 1

The mundane odd jobbing jobs

Leaky HGV inspection pit gets a steel liner! Part 2

Leaky HGV inspection pit gets a steel liner! Part 1

Finishing the Protech Post Knocker.

Rusty hole in diesel tank! Cut out and replace.

Another Protech post knocker!

Putting a new floor in a ROTTEN telehandler bucket!

Fitting press arm on Dowdeswell plough

Fixing worn stone picker rotor and boring out Toyota forklift axle

Redesigning the Nissan powered Grey Fergie! Part 2

Redesigning the Nissan powered Grey Fergie! Part 1

Shortening combine shaft and repairing McConnel discaerator bracket

Heath Super Chaser needing some attention. REASSEMBLING! Final

Heath Super Chaser needing some attention. Cracked chassis! Part 2

Heath Super Chaser needing some attention, worn out pivots. Part 1

Trying and failing to get my tractor puller ready!

Repairing a centrifugal slurry pump. Part 2

Repairing a centrifugal slurry pump. Part 1

The baler flywheels keep coming! and altering some tractor wheel centres

Welding job on bale shredder and repairing baler auger

Fixing a broken top grab. Made out of too thin steel!

Broken! JCB TM headstock in a bad way!

Rebuilding COMPLETELY worn out skid steer toe tip bucket! FINAL!!

Making a weight frame and tow hitch for a super farm tractor puller

Rebuilding COMPLETELY worn out skid steer toe tip bucket! Part 3

Rebuilding COMPLETELY worn out skid steer toe tip bucket! Part 2

Rebuilding COMPLETELY worn out skid steer toe tip bucket! Part 1

Fabricating a turbo shield for a tractor puller and emergency repair on a drawbar.

Badly worn John Deere telehandler headstock! Part 2.

Badly worn John Deere telehandler headstock! Part 1

Replacing Joskin tanker axle pivot. Part 2.

Pressing stuck shafts out with 50tonne jack! JOSKIN axle pivot. Part 1.

Just not made strong enough! Protech post knocker.

Saving a rotten flail mower!

Fabricating pipe frame for a John Deere tractor

Welding up leaky tanker, flame cutting John Deere weight and mole ploughing in water pipe.

Reinforcing frame for slurry tanker booms

Insulating my workshop roof to help stop me freezing in winter!

Repairs on Massey Ferguson 128 baler

Rebuilding badly damaged Strimech muck grab.

Cutting out broken wheel centres and welding in replacements.

Odd jobbing. Machining Baler part and repairing beet harvested turbine wheel.

Escaping the workshop and building myself a log shed with left over materials.

Changing brackets on bucket from Merlo to JCB

Odd jobbing. Trailer drawbar ring, rolling plate and fabricating a frame.

Line boring Wacker Neuson mini telehandler axle with my new jig.

Making a line boring Jig for my Siegmund fixture table.

Fixing a dodgy made bale spike and a weak Triffitt trailer head board

Making a roller, adding a spool block to the log splitter and splitting some MASSIVE logs.

Changing a bucket edge and drilling and skimming baler flywheel

Straightening bent hydraulic tailgate on Stewart trailer

Sorting out a worn headstock on a JCB 526-56. Part 2

Sorting out a worn headstock on a JCB 526-56. Part 1

Herbst low loader trailer in a bad way! Its finally finished! Part 3

Herbst low loader trailer in a bad way! Let the rebuild begin! . Part 2

Fabricating a tree puller for the front of a Compact loader. Part 2